500W 600W Fiber-optic Transmission Energy Negative Feedback Laser Welding Machine
|
model |
SIB-500WH |
SIB-500WM |
SIB-500W |
||
|
Laser wavelength |
1064nm |
||||
|
Maximum output optical power |
550W |
||||
|
Maximum pulse energy |
100J |
90J |
80J |
||
|
Maximum peak power |
10KW |
9KW |
8KW |
||
|
Pulse width |
0.1-20ms |
||||
|
Pulse repetition rate |
1-200HZ |
||||
|
Welding penetration (stainless steel) |
3.0mm |
2.5mm |
2.0mm |
||
|
Welding penetration (carbon steel plate) |
3.0mm |
2.5mm |
2.0mm |
||
|
Welding penetration (pure aluminum) |
2.0mm |
1.5mm |
1.2mm |
||
|
Welding penetration (red copper) |
2.0mm |
1.5mm |
1.2mm |
||
|
Welding penetration (brass) |
2.0mm |
1.5mm |
1.2mm |
||
|
Spectroscopic mode |
Precision energy spectroscopy or high-speed time spectroscopy |
||||
|
Closed loop feedback control mode*** |
Real time control of energy negative feedback with arbitrary waveform |
||||
|
Energy fluctuation*** |
<±3% *** |
||||
|
Optical fiber coupling system |
With optional water cooling and optical fiber in place alarm function |
||||
|
Optical fiber model*** |
SI200 300 400 600/ GI400 600 Leoni double cladding, pure imported core, 5m / 10m / 15m / 20m / 30m optional |
||||
|
Number of optical fiber paths |
≤6（Standard single optical path） |
||||
|
Aiming and positioning mode |
Laser diode red light indication (CCD optional) |
||||
|
Cooling mode |
External chiller (external circulating water flow alarm) |
||||
|
Device power consumption |
18KW |
||||
|
Air switch*** |
The main line is equipped with undervoltage, overvoltage and power-off protection. |
||||
|
Power requirements |
AC380V±10% 50/60Hz |
||||
|
Internal circulation performance*** |
With water level, water temperature and water flow. Water conductivity alarm function |
||||
|
Internal circulation system |
Epoxy resin filtration (standard water pump 50Hz, customized for area 60Hz) |
||||
|
Host size |
1460*660*1080mm |
1460*660*1080mm |
1360*660*1080mm |
||
Product Features
Energy negative feedback control system
Energy negative feedback control refers to a method where the desired output laser energy waveform is compared in real-time with the actual output energy waveform to determine the input power level of the pump lamp. The system automatically controls the power level inputted by the pump lamp to be consistent each time, thereby controlling the output energy to be consistent.
Arbitrary waveform setting
In practical processing and production, materials such as copper, aluminum, and gold, due to their high surface reflectivity to 1064nm wavelength laser, may lead to issues such as insufficient processing intensity and unsightly welding surfaces during the processing. For materials like high-carbon steel, rapid cooling and heating can cause problems like cold and hot cracks during processing. To address these issues, the energy waveform of the laser pulse is set to control the variation of laser energy during welding.
Through energy negative feedback control technology, the actual output energy of the laser can be precisely controlled within a range of 3%. At the same time, it addresses the following issues that cause large fluctuations in laser output energy: A. Market fluctuations affecting the fluctuation of laser output energy; B. Variability in each discharge of the xenon lamp; C. Decrease in output energy due to aging of the xenon lamp; D. Fluctuations in laser output energy caused by factors such as changes in water flow rate and water temperature.
Due to the aforementioned reasons, conventional laser welding equipment cannot effectively ensure the consistency of welding quality. Furthermore, as the pump lamp ages continuously during use, welding parameters need to be adjusted periodically. To maintain a stable and good processing state and reduce product defects, it is essential for the laser energy and its waveform output to exhibit good repeatability and consistency. Energy negative feedback technology is the most effective method to address this issue. Additionally, there is no need to adjust welding parameters during use, as the pump lamp can be used until it reaches the end of its lifespan.
Four language operation interfaces
It supports the switching of multiple language operation interfaces, currently including Simplified Chinese, Traditional Chinese, English, Vietnamese, and Korean. More operation interfaces are being improved in the future
500W/600W fiber-optic transmission energy negative feedback laser welding machine
500W fiber-optic transmission energy negative feedback laser welding machine
Battery Series
All hardware, circuits, software, and controls of our power supplies are independently developed and produced by our company, possessing complete independent intellectual property rights. Our power supplies exhibit the following characteristics:
A. All power supplies have energy negative feedback function;
B. Support multi-channel independent output customization;
C. Support differentiated customization, including customization of the operation interface and operation language;
Support functional expansion and customization, such as integration with MES systems
Energy Fiber Series
Our energy fiber includes two major series: SI and GI. Each fiber undergoes strict quality control. Currently, we ship 3,000 units annually. Our products have the following characteristics:
1. Multiple core diameters and lengths are available;
2. Support customization of exotic fibers, such as square, diamond, etc;
3. Support for optional water-cooled structure for better protection of optical fibers;
Support customization of quartz end cap structure, capable of withstanding higher power